Predictive and inverse modeling of a radionuclide diffusion experiment in crystalline rock at ONKALO (Finland)

Soler, J. M.*; Keklinen, P.*; Pulkkanen, V.-M.*; Moreno, L.*; Iraola, A.*; Trinchero, P.*; Hokr, M.*; ha, J.*; Havlov, V.*; Trpkoov, D.*; et al.

Nuclear Technology, 209(11), p.1765 - 1784, 2023/11

https://doi.org/10.1080/00295450.2023.2209234

Development plan for coupling technology between high temperature gas-cooled reactor HTTR and hydrogen production facility, 1; Overview of the HTTR heat application test plan to establish high safety coupling technology

Nomoto, Yasunobu; Mizuta, Naoki; Morita, Keisuke; Aoki, Takeshi; Okita, Shoichiro; Ishii, Katsunori; Kurahayashi, Kaoru; Yasuda, Takanori; Tanaka, Masato; Isaka, Kazuyoshi; et al.

Proceedings of 30th International Conference on Nuclear Engineering (ICONE30) (Internet), 7 Pages, 2023/05

Irradiation test using foreign reactor, 1; Study of irradiation test with capsule temperature control system (Joint research)

Takabe, Yugo; Otsuka, Noriaki; Fuyushima, Takumi; Sayato, Natsuki; Inoue, Shuichi; Morita, Hisashi; Jaroszewicz, J.*; Migdal, M.*; Onuma, Yuichi; Tobita, Masahiro*; et al.

JAEA-Technology 2022-040, 45 Pages, 2023/03

JAEA-Technology-2022-040.pdf:6.61MB

Because of the decommission of the Japan Materials Testing Reactor (JMTR), the domestic neutron irradiation facility, which had played a central role in the development of innovative nuclear reactors and the development of technologies to further improve the safety, reliability, and efficiency of light water reactors, was lost. Therefore, it has become difficult to pass on the operation techniques of the irradiation test reactors and irradiation technologies, and to train human resources. In order to cope with these issues, we conducted a study on the implementation of irradiation tests using overseas reactors as neutron irradiation sites as an alternative method. Based on the "Arrangement between the National Centre for Nuclear Research and the Japan Atomic Energy Agency for Cooperation in Research and Development on Testing Reactor," the feasibility of conducting an irradiation test at the MARIA reactor (30 MW) owned by the National Centre for Nuclear Research (NCBJ) using the temperature control system, which is one of the JMTR irradiation technologies, was examined. As a result, it was found that the irradiation test was possible by modifying the ready-made capsule manufactured in accordance with the design and manufacturing standards of the JMTR. After the modification, a penetration test, an insulation continuity test, and an operation test in the range of room temperature to 300C, which is the operating temperature of the capsule, were conducted and favorable results were obtained. We have completed the preparations prior to transport to the MARIA reactor.

Radioactive particles from a range of past nuclear events; Challenges posed by highly varied structure and composition

Johansen, M. P.*; Child, D. P.*; Collins, R.*; Cook, M.*; Davis, J.*; Hotchkis, M. A. C.*; Howard, D. L.*; Howell, N.*; Ikeda, Atsushi; Young, E.*

Science of the Total Environment, 842, p.156755_1 - 156755_11, 2022/10

https://doi.org/10.1016/j.scitotenv.2022.156755

Study on the effect of long-term high temperature irradiation on TRISO fuel

Shaimerdenov, A.*; Gizatulin, S.*; Dyussambayev, D.*; Askerbekov, S.*; Ueta, Shohei; Aihara, Jun; Shibata, Taiju; Sakaba, Nariaki

Nuclear Engineering and Technology, 54(8), p.2792 - 2800, 2022/08

https://doi.org/10.1016/j.net.2022.02.026

Applicability of equivalent linear analysis to reinforced concrete shear walls; 3D FEM simulation of experiment results of seismic wall ultimate behavior

Ichihara, Yoshitaka*; Nakamura, Naohiro*; Moritani, Hiroshi*; Horiguchi, Tomohiro*; Choi, B.

Nihon Genshiryoku Gakkai Wabun Rombunshi, 21(1), p.1 - 14, 2022/03

https://doi.org/10.3327/taesj.J20.038

In this study, we aim to approximately evaluate the effect of nonlinearity of reinforced concrete structures through seismic response analysis using the equivalent linear analysis method. A simulation analysis was performed for the ultimate response test of the shear wall of the reactor building used in an international competition by OECD/NEA in 1996. The equivalent stiffness and damping of the shear wall were obtained from the trilinear skeleton curves proposed by the Japan Electric Association and the hysteresis curves proposed by Cheng et al. The dominant frequency, maximum acceleration response, maximum displacement response, inertia force-displacement relationship, and acceleration response spectra of the top slab could be simulated well up to a shear strain of approximately =2.010. The equivalent linear analysis used herein underestimates the maximum displacement response at the time of ultimate fracture of approximately =4.010. Moreover, the maximum shear strain of the shear wall could not capture the locally occurring shear strain compared with that of the nonlinear analysis. Therefore, when employing this method to evaluate the maximum shear strain and test results, including those during the sudden increase in displacement immediately before the fracture, sufficient attention must be paid to its applicability.

Characterizing the reactivation mechanisms of coseismic surface ruptures associated with the 2011 Mw 6.7 Fukushima-ken Hamadori earthquake in Japan through borehole hydromechanical testing

Guglielmi, Y.*; Aoki, Kazuhiro; Cook, P.*; Soom, F.*; Cappa, F.*; Tanaka, Yukumo

Tectonophysics, 819, p.229084_1 - 229084_22, 2021/11

https://doi.org/10.1016/j.tecto.2021.229084

The reactivation mechanisms of coseismic surface ruptures associated with the 2011 Mw 6.7 Fukushima-ken Hamadori earthquake in Japan are investigated using in-situ controlled hydraulic injections in subsurface boreholes. Two fault segments were selected for reactivation studies, one across a coseismic rupture, the Shionohira site, and one across a non-coseismically ruptured segment, the Minakami-kita site. A series of water injections in sealed sections of boreholes set across the fault progressively bring the fault to rupture by a step-by-step decrease of the effective normal stress clamping the fault. While the fault is rupturing during these hydraulic stimulations, borehole displacements, fluid pressure and injection flowrate are continuously monitored. Then, the tests were analyzed using fully coupled hydromechanical modeling. The model was calibrated on field data, and a parametric study was conducted to examine the modes of fault reactivation. Coseismic surface rupture of the Shionohira fault showed a pure dilatant slip response to hydraulic tests, while the tectonically un-activated Itozawa fault (South) indicated a complex hybrid response to tests related to both a higher frictional and cohesive strengths of the fault. The analysis of the induced Shionohira slip event showed that it is reasonably modeled as a Coulomb rupture with an eventual dependency of friction on slip velocity, in good accordance with laboratory-derived rate-and-state friction data on the Shinohira gouge samples. In contrast, the Itozawa fault reactivation mechanism appears dominated by tensile failure with limited Coulomb shear failure. Thus, the applied protocol proves to be able to isolate significant differences in fault physical properties and rupture mechanisms between two segments of the same fault system, opening perspectives to better assess near-surface rupture effects, and therefore the safety of structures subject to large earthquakes.

Quantifying the porosity of crystalline rocks by in situ and laboratory injection methods

Mri, A.*; Mazurek, M.*; Ota, Kunio; Siitari-Kauppi, M.*; Eichinger, F.*; Leuenberger, M.*

Minerals (Internet), 11(10), p.1072_1 - 1072_17, 2021/10

https://doi.org/10.3390/min11101072

Evaluation of brittle crack arrest toughness for highly-irradiated reactor pressure vessel steels

Iwata, Keiko; Hata, Kuniki; Tobita, Toru; Hirota, Takatoshi*; Takamizawa, Hisashi; Chimi, Yasuhiro; Nishiyama, Yutaka

Proceedings of ASME 2021 Pressure Vessels and Piping Conference (PVP 2021) (Internet), 7 Pages, 2021/07

Feasibility study on tritium recoil barrier for neutron reflectors of research and test reactors

Kenzhina, I.*; Ishitsuka, Etsuo; Ho, H. Q.; Sakamoto, Naoki*; Okumura, Keisuke; Takemoto, Noriyuki; Chikhray, Y.*

Fusion Engineering and Design, 164, p.112181_1 - 112181_5, 2021/03

https://doi.org/10.1016/j.fusengdes.2020.112181

Tritium release into the primary coolant during operation of the JMTR (Japan Materials Testing Reactor) and the JRR-3M (Japan Research Reactor-3M) had been studied. It is found that the recoil release by Li(n,)H reaction, which comes from a chain reaction of beryllium neutron reflectors, is dominant. To prevent tritium recoil release, the surface area of beryllium neutron reflectors needs to be minimum in the core design and/or be shielded with other material. In this paper, as the feasibility study of the tritium recoil barrier for the beryllium neutron reflectors, various materials such as Al, Ti, V, Ni, and Zr were evaluated from the viewpoint of the thickness of barriers, activities after long-term operations, and effects on the reactivities. From the results of evaluations, Al would be a suitable candidate as the tritium recoil barrier for the beryllium neutron reflectors.